ATA8741-PXQW【PDF 7/238 页】MCU W/TRANSMITTER ASK/FSK 24QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录52

3页 4页 5页 6页 [7页]8页 9页 10页 11页

9140CINDCO02/10

ATA8741

3. Functional Description

For a typical application 3 to 4 interconnections between the AVR and the transmitter are

required (see Figure 1-1 on page 2 and Figure 1-2 on page 3). The CLK line is used to allow the

microcontroller to generate an XTAL-based transmitter signal. The ENABLE line is used to start

the transmitters XTO, PLL, and clock. The PA_ENABLE line is used to enable the power ampli-

fier in ASK and FSK mode. In FSK mode a fourth line is necessary to modulate the load capacity

of the XTAL. To wake up the system from standby mode at least one key input is required. After

pressing the key, the microcontroller starts up with the internal RC oscillator. For TX operation

user software must control ENABLE, PA_ENABLE, and XTAL load capacity as described in the

following section.

If ENABLE = L and PA_ENABLE = L the transmitter and the microcontroller (MCU) are in

standby mode, reducing the power consumption so that a lithium cell can be used as power sup-

ply for several years.

If ENABLE = H and PA_ENABLE = L, the XTO, PLL, and the CLK driver from the transmitter are

activated. The crystal oscillator together with the PLL from the RF transmitter typically require

< 3 ms until the PLL is locked and the clock output (Pin 8) is stable.

If ENABLE = H and PA_ENABLE = H, the XTO, PLL, CLK driver, and the power amplifier (PA)

are switched on. ASK modulation is achieved by switching on and off the power amplifier via

PA_ENABLE. FSK modulation is achieved by switching on and off an additional capacitor

between the XTAL load capacitor and GND, thus changing the reference frequency of the PLL.

This is done using a MOS switch controlled by a microcontroller output. The power amplifier is

switched on via PA_ENABLE = H.

The MCU has to wait at least > 3 ms after setting ENABLE = H, before the external clock can be

used. The external clock is connected via the timer0 input pin that clocks the USI from the MCU

to achieve an accurate data transfer. The frequency of the internal RC oscillator is affected by

ambient temperature and operating voltage.

The USI provides two serial synchronous data transfer modes, with different physical I/O ports

for the data output. The two wire mode is used for ASK and the three wire mode is used for FSK.

If ENABLE = L and the PA_ENABLE = L, the circuit is in standby mode consuming only a very

small amount of current so that a lithium cell used as power supply can work for several years.

With ENABLE = H the XTO, PLL, and the CLK driver are switched on. If PA_ENABLE remains L

only the PLL and the XTO are running and the CLK signal is delivered to the microcontroller.

The VCO locks to 32 times the XTO frequency.

With ENABLE = H and PA_ENABLE = H the PLL, XTO, CLK driver, and the power amplifier are

on. With PA_ENABLE the power amplifier can be switched on and off, which is used to perform

the ASK modulation.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式